Standard Kits - Timber leaves
Portman's pocket door system has been designed to allow you the design flexiblity you need when specifying a sliding pocket door.
The necessary wall aperture dimensions for the single or double Portman pocket doors can be derived from the calculations and elevations shown bottom right.
For doors over 2700mm high or 1500mm wide, please contact the sales office. If ordering for frameless glass door leaves (individual leaf up to 1280mm wide only), please choose from the standard/intermediate kits below and P880 (doors up to 800mm wide) or P1280 (doors up to 1280mm wide) glass clamps and timber jambs from Accessories
View closing options on the self-closing and powered opening/closing page.
To see how easy Portman is to install, view the Portman installation instructions (PDF 1.7Mb) or watch the installation animation.
Single Doors
Standard door leaves (up to 2100mm high)
| Description | Part Ref's |
|---|---|
| Standard width door leaf | |
| 626-926mm wide x up to 2100mm high | P7001 SD Add to specification |
| Intermediate width door leaf | |
| 927-1300mm wide x up to 2100mm high | P7001 ID Add to specification |
| Wide door leaf | |
| 1301-1500mm wide x up to 2100mm high | P7001 WD Add to specification |
Tall door leaves (up to 2700mm high)
| Description | Part Ref's |
|---|---|
| Tall door leaf | |
| 626-926mm wide x up to 2700mm high | P7001 TD Add to specification |
| Tall/Intermediate width door leaf | |
| 927-1300mm wide x up to 2700mm high | P7001 ITD Add to specification |
| Tall/Wide door leaf | |
| 1301-1500mm wide x up to 2700mm high | P7001 WTD Add to specification |
For doors over 2700mm high or 1500mm wide please contact the sales office.
View closing options on the self-closing and powered opening/closing page.
If self-closing/damper units are required, please request at time of order.
If ordering for frameless glass door leaves (individual leaf up to 1280mm wide
only), please choose “0”-suffixed kit.
Dimensions (max door thickness 44mm)
Single Door
Wp = Door panel width
Hp = Door panel height
W = (2Wp)+11mm
H = Hp+95mm
Sp = Wp-9mm
Op = Wp-23mm
Oh = Hp-7mm
Decide what is your constraining factor. Either the door leaf size OR the available wall aperture will decide what should be specified.
Use the calculations above to derive the correct wall aperture or door leaf
Double Doors
Standard door leaves
(up to 2100mm high)
| Description | Part Ref's |
|---|---|
| Standard width door leaf | |
| 626-926mm wide x up to 2100mm high | P7001 DD Add to specification |
| Intermediate width door leaf | |
| 927-1300mm wide x up to 2100mm high | P7001 IDD Add to specification |
| Wide door leaf | |
| 1301-1500mm wide x up to 2100mm high | P7001 WDD Add to specification |
Tall door leaves
(up to 2700mm high)
| Description | Part Ref's |
|---|---|
| Tall door leaf | |
| 626-926mm wide x up to 2700mm high | P7001 TDD Add to specification |
| Tall/Intermediate door leaf | |
| 927-1300mm wide x up to 2700mm high | P7001 ITDD Add to specification |
| Tall/Wide door leaf | |
| 1301-1500mm wide x up to 2700mm high | P7001 WTDD Add to specification |
If simultaneous opening/closing is required please state at time of order.
View closing options on the self-closing and powered opening/closing page.
Self closing and simultaneous opening cannot be specified together.
For intermediate and wide double doors kits please contact the sales office.
Dimensions (max door thickness 44mm)
Double Door
Wp = Door panel width
Hp = Door panel height
W = (4Wp)-16mm
H = Hp+95mm
Sp = Wp-9mm
Op = (2Wp)-34mm
Oh = Hp-7mm
Decide what is your constraining factor. Either the size of the two door leaves OR the available wall aperture will decide what should be specified.
Use the calculations above to derive the correct wall aperture or door leaves that can be installed.